null This knife setting is suitable for Weihong (Ncstudio), Beijing Jingdiao, Xindai (SYNTEC), Baoyuan (LNC), Shanlong (PELYCOSAE), FANUC, FAGOR, and MITSUBISHI ), MACH3 and other various control systems, please consult the system and equipment manufacturers in detail before purchasing, whether they support the tool setting function and determine the tool setting wiring port
Normally closed specifications
Brand: Hongyang Product name: automatic tool setting instrument for engraving machine Stroke: 5mm Output mode: B:NC Pre-travel: almost zero Repeatability: 0.001mm Protection structure: IP67 Contact force: 1.5N Contact material: cemented carbide Shell material: grinding 4S Protection tube: 1m minimum bending radius R25 LED light: normally open and off when working Cable: 3m oil resistant 4 core diameter 5 Alarm signal when the stroke is exceeded: B: NC (normally closed) [distance measurement signal about 2.5mm] Electric shock rating: DC24V 20mA (MAX) recommended value 10mA (resistive load)
Normally open specifications
Output mode: A: NO (normally open) Pre-stroke: about 0.5mm Stroke: about 0.5mm Repeatability: B:NC Pre-travel: almost zero Repeatability: 0.001mm Protection structure: IP67 Contact force: IP67 Contact material: cemented carbide Shell material: grinding 4S Protection tube: 1m minimum bending radius R25 LED light: normally open and off when working Cable: normally open, closed when working Electric shock life: 3 million times Electric shock rating: DC24C 20mA (MAX) Alarm signal when the stroke is exceeded: (normally closed) [distance measurement signal about 2.5mm] Electric shock rating: DC24V 100mA (MAX) recommended value 10mA (resistive load)
Two types of wiring
Consult customer service for specific details
Control card wiring board GND connected to tool setting instrument machine tool signal Control card Tool setting instrument Tool setting signal on the tool setting instrument The remaining 2 power cords do not need to be connected
Normally closed 4-wire circuit diagram
Normally open 6-wire circuit diagram
Power supply voltage: DC24V Current consumption: 10mA Output specifications: DC60V 100mA (resistive load)/AC60V/100mA (peak value)/500mW (Max)
Matters needing attention in the use of tool setting instrument
1, contact can not exceed the tool alignment instrument stroke, will make the tool alignment instrument damage,(stroke is 5.0mm) 2. Do not immediately release the contact surface of the tool setting instrument by hand, so as not to damage the internal structure of the tool setting instrument and affect the service life and efficiency. 3. After the tool and tool alignment instrument is finished, the tool must be lifted vertically away from the contact surface, and do not move laterally or it will damage the tool alignment instrument.
Sturdy material
The contact surface of the tool and the tool setter must be vertical and vertically downward to contact the contact surface. Try to install it on the workbench where there is less iron filings, so as not to affect the accuracy of the tool setter.
In any direction
In the rated power supply range, the use voltage is controlled at DC10-30V, the current is below 20mA, and the use temperature range is -25°C-70°C. The use effect is better.
Fully equipped
The diameter of the tool setting tool should be controlled below 20mm, and the tool setting speed should be controlled at 50-200mm/min The tool center should fall on the center of the tool facing.
Easy and effortless
When using the blow-up function, the outer diameter of the air pipe is 6mm in diameter, and the inner diameter is 4-5mm in diameter. Pay attention to hygiene when using it, and clean the oil on the contact surface.
Company information and contact information
Jinan Hongyang CNC Machinery Co., Ltd. was established in 2008. There are more than 100 employees, and the inventory area is 10,000 square meters. It is mainly engaged in engraving machine parts, including spindle motor, frequency converter, stepper motor, drive, hybrid servo motor, servo motor, Richauto dsp series controller, weihong or nc studio controller, spindle cooling water pump, lubricating oil pump, tool sensor, Limit sensors, water-cooled vacuum pumps, air-cooled vacuum pumps, power supplies, transformers, gear boxes, racks, rails, sliders or blocks, ISO30 tool clips, cable chains, spindle dust covers, vacuum cleaners and other engraving machine accessories, welcome your For inquiries. Contact information WeChat whatsapp mobile 8615650000988 lily @ hycncrouter. com
