1 &220vAC 1.5kw ER16 CNC Water Cooled Spindle Motor engraving milling grinding 80x220mm 4 pcs bearings
Size:80x220mm(Middle body diameter:80mm;Length:220mm)
Speed Ways:Through 3-phase output inverter and adjust the inverter frequency to change the spindle speed.
Cooling:Water cooling
Power Interface:Optional H20-4 pins waterproof air plug. The air plug marked "1 ","2"," 3"," 4", "1 ","2 ","3" were connected to inverter (U, V, W), 4 connected inverter ground.(Pay attention! our spindle "4" connecting to GND,promised personal safety!!)
Power:1.5kw (1HP=725w)
Voltage:220vAC(If you need 110v/380v spindle ,please leave message to us,thank you)
Current:7A
Frequency:0-400Hz
Speed:0-24000rpm
Runout Off:0.01m
Diameter(mm):80mm
Bearing Type:2×7004C P4 DT&2×7002C P4 DT
4pcs fully sealed angular contact bearings
Collet:ER16
ClipKnifediameter:1mm,2mm,3mm,3.175mm,4mm,5mm,6mm,6.35mm,7mm,8mm,9mm,10mm.
Water Cooling ER16 collet chunk
Grease Lubrication
Main Application:Engrave for wood,bamboo,normal PCB,PVC,PMMA,plastic,duotone board(ABS)and etc nonmetal, also can engrave on gold,silver,copper, aluminium,Pb etc soft metal surface working.
4 P4 angular contact bearings ,2×7002C P4 DT&2×7000C P4 DT,increase spindle life
Longer length make the torque bigger,more powerful.
Carefull assembly make the spindle more precisional.
Runout off 0.01mm.Coaxial degree less than 0.0025mm
Shipment within 4 days,promise the delivery time.
We are thespindlemanufacturer,we offer onlybest qualityandbest priceto you.
Tip: The spindle size 80x220mm, longer than the average 1.5kw spindle.
Spindle torque is greater than the other brands. Quality is very good.
1. Our Ceramic ball bearings spindle use4 pcs ceramic ball bearings.
2. Ceramic ball bearings are resistant tohigh temperatures and low heat, usually 3-5 degrees lower than steel ball bearings during using .
3. Ceramic ball bearings havelow friction,low noiseandlong service life.
4.If you want to use the spindle for aluminum, hard wood, then ceramic ball bearings better than steel ball bearings.
Spindle working environment temperature is usually -10 ~ 40 .
Before installing the first electric spindle axis head turned by hand, should feel flexible, non-blocking phenomenon.
Spindle in the preservation and transportation, high-speed grease inside the bearing state will change, customers should be running at low speed for 30 minutes. 3000 rpm and then follow the poor increase, run 20 minutes each. Spindle and the inverter should be working together. The inverter's specifications and parameter settings need match spindles parameter.
Connect the inverter spindle, three-phase inverter power cord should be soldered in the plug 1 (U), 2 (V), 3 (W) feet, 4 feet for the ground. After the power is turned on, to observe whether the spindle rotation axis indicates the direction consistent. If inconsistency should be immediately shut down, replace the inverter and spindle connected two wires of three-phase power supply.
It should ensure that before use of water-cooled spindle, the cooling system is working properly. Every day before using the spindle must be running at low speed for 15-20 minutes. Clamping the cutters to spindle, collet nuts ,collets,cutters must be clean enough. Shank inserted into the collet must be greater than 15mm.
Water cooled spindleMUSTbe used with water pump. Otherwise the spindle will soon broken.
AC spindle motorMUSTuse with inverter. The power of inverter need equal or bigger than the spindle power. Before using,please set up the inverter parameters suitable for spindle. Otherwise the spindle and inverter will broken at once.
When you use the spindle,the noise is not same as always,pleaseSTOPthe spindle at once. You may need to replace the spindle bearings.
Before shipping , we did the oil seal to avoid the rust during the long shipment. When you get the spindle, please clearing the oil seal before using. Thank you.
1. Cooling in different ways: water-cooled spindle motor is the use of the water cycle to cool the heat generated after the high-speed rotating spindle, spindle motor with fan-cooled approach to cooling.
2. Noise: Water-cooled spindle motor is basically no noise, but the air-cooled spindle motor is very loud.
3. Life aspects: Water-cooled spindle motor pay attention to maintenance, frequently changes the water or the use of industrial water coolers, air-cooled spindle fan mainly by the wind blowing the heat transferred to the heat sink, so as to achieve the cooling effect.
4.If you need use for metal ,hard wood,granite,stone,you can choose metal spindle.Metal spindle much better than wood spindle
We will 100% guarantee security to the hands of the guests.
Spindle from the production - assembly - test, and finally the perfect packaging .
Shipping Cost:
Our products are sold worldwide.
If you need many items in the same time, please contact us in advance to confirm shipping cost.
Payment:
We accept paypal credit, bank transfer, western union etc.
Payment must be made within 7days calendar days of the auction end time.
Problem and Feedback:
PLEASE DON'Tleave any negative feedback before you contact us.
We are honest and helpful supplier , we will try our best to solve problems with you.
Your satisfaction is very important for our store, so please contact us before you want to leave a negative feedback.
Thanks very much in advance.
Refund:
If you areNOT SATISFIEDwith our package like the products is damage, please do not sign it and contact us immediately.
If it is possible, please take some photos or make a small video about it. It will help us to solve the problems.
Note:
We can produce the product according to our customer's design.
If you need something is very special, please contact us about it.
We are willing to help you about it.
