1&1.5kw spindle motor
1&1.5kw inverter/VFD
1&Φ80mm spindel clamp/halterung
1&3.5m water pump&5mWasser rohre
1 kit ER11 hohe genauigkeit collet (≤0,008mm)
good news ! Order 1.5kw ER11 water-cooled spindle kit now, you will get 1 kit ER11 high precision collet as a gift (accuracy≤0.008)
Power: 1.5 kW
Voltage: 220v
Current: 5A
Frequency: 400Hz
Speed: 0-24000rpm
Runout: less than 0.01mm
Diameter (mm): 80
Bearing type: 2x7005 P4 DT & 2x7003 P4 DT
4 fully sealed ball bearings
Chuck: ER11
Water-cooled ER11 chuck block
Grease lubrication
Main use: used for wood, stone, bamboo, ordinary PCB, PVC, PMMA, plastic, bamboo, two-tone board (ABS) and other non-metallic carving.
●The working environment temperature of the spindle is usually -10~40.
●Before installing the first electric spindle to rotate the spindle head by hand, you should feel flexibility and no blockage.
P4 fully sealed angular joint bearings can extend the life of the spindle.
The longer the length, the greater the torque and the greater the power.
Careful assembly makes the spindle more precise.
The accuracy is 0.01mm, and the coaxial cable is less than 0.0025mm
1. Our main shaft uses 4 bearings.
2. Bearings are resistant to high temperature and low heat
3. The ball bearing has low friction, low noise and long service life.
Power: 1.5kw Input Voltage: 220v
Input Frequency: 50/60Hz Input Phase: 1 phase
Output Voltage: 220v Output Phase: 3 phase
Output Current: 7.0A Output Frequency: 0-650Hz
Control Method: V/F control; Open-loop flux vector control
◆Two speed control modes: no PG vector control (SVC), V/F control
◆ Vector control without PG (SVC): starting torque 0.5 Hz, maximum 150%
◆ 8-segment simple PLC function, multi-segment speed control and pid control
◆Support multiple frequency settings: digital settings, analog settings, PID settings, RS485 communication settings
◆ I/O terminals can be freely programmed to combine multiple working modes according to user needs.
◆With frequency hopping control function, it can effectively suppress mechanical resonance and make the system more stable and reliable.
◆It has the function of instantaneous power-off retention, which can avoid the impact on production due to instantaneous power-off
◆With over-torque and under-torque detection
◆Automatic voltage setting function, effectively solve the problem of low frequency vibration of high-power motors
◆Provide multiple fault protection functions: overcurrent, overvoltage, undervoltage, overheat, overload, lack of real-time monitoring and protection to ensure safe operation
Maximum head: 3.5m Power: 80w
Maximum flow: 3500L/H Plug cable length: 1.5m
Voltage: 220-240V Frequency: 50Hz
Faucet: 8mm size: 145x79x92mm
Advantage
High lift
Large Flow
Highly durable
Excellent insulation
Can cool down the machine quickly
Good quality and long life
Large inventory
A tremendous strength
The shell is made of high-quality plastic, which is corrosion-resistant and highly durable.
Since the motor bearings are completely sealed, the pump has excellent insulation properties.
Pump combination pump, filtration, oxygen and fountain solution are combined into one.
Must be used in water.
Once the product does not work properly, the power must be cut off, and maintenance must be performed after it is lifted from the water.
Basic parameters
Diameter: 80 mm Material: cast aluminum
Features
Cast aluminum fixtures are high-quality aluminum cast by a special manufacturing process. Compared with ordinary aluminum, this product has the characteristics of toughness, strong impact resistance, high hardness and strong oxidation resistance.
Product Description
Compared with aluminum profile clamps, it has higher precision and is not easy to deform.
The inner wall is smooth, and the outer wall is sandblasted, which is fine and uniform, but not very smooth.
Cast aluminum fixtures are much heavier than aluminum profile fixtures.
Usage
The cast aluminum fixture is mainly used to fix the auxiliary product, thus ensuring the verticality of the auxiliary product and the balance piece, improving the operation accuracy of the auxiliary product, reducing the noise and reducing the accumulated error.
Basic parameters
Material: 65Mn steel
Accuracy≤0.008mm
Hardening and precision grinding
It is widely used in boring, milling, drilling, wire tapping of CNC milling machine, engraving spindle machine, machining center and other processing.
●When the spindle is stored and transported, the bearing condition inside the high-speed grease will change, and the customer should run it at low speed for 30 minutes. Then increase slowly at a speed of 3000 rpm, running for 20 minutes each time. The spindle and inverter should work together. The specifications and parameter settings of the inverter match the spindle parameters.
●To connect the inverter main shaft, the three-phase inverter power cord should be welded to the plug 1 (U), 2 (V), 3 (W) pin, and the grounded pin 4. After turning on the power, observe whether the spindle rotation axis always shows the direction. If it is inconsistent, turn it off immediately, and replace the two wires of the three-phase power supply connected to the inverter and the spindle.
●Before using the spindle every day, it must run at low speed for 15-20 minutes. Clamp the cutter on the spindle, the chuck nut, chuck, and cutter must be clean enough. The shank inserted into the chuck must be larger than 15mm.
●The water-cooled spindle must be used together with the water pump. Otherwise, the spindle will quickly break.
●The AC spindle motor must be used together with the inverter. The power of the inverter needs to be equal to or greater than the power of the spindle. Before use, please set the inverter parameters suitable for the spindle. Otherwise, the spindle and inverter will break immediately.
●When using the spindle, the noise is different from before, so please stop the spindle immediately. You need to replace the spindle bearing.
1. Different cooling methods: The water-cooled spindle motor uses water circulation to cool the heat generated after the spindle rotates at a high speed, and the spindle motor uses fan cooling for cooling.
2. Noise: The water-cooled spindle motor is basically no noise, but the air-cooled spindle motor is very large.
3. Life: water-cooled spindle motor should pay attention to maintenance, often change water or use industrial water cooler, air-cooled spindle fan mainly blows heat to the heat sink by wind to achieve cooling effect.
4. If you need to use metal, hardwood, granite, stone, you can choose metal mandrel. Metal mandrels are much better than wooden mandrels.
●The spindle frequency power supply is connected to the rated voltage, and the frequency should be consistent with the technical parameters of the electric spindle. The spindle speed can be adjusted to change the frequency, and the voltage changes in proportion.
●Do not use the spindle, apply compressed air to blow off the static coolant in the pipeline. To prevent rust, please plug the water hole. The spindle should be oiled. Add anti-wave device and put it in a dry place.
●To replace the spindle bearing, some professional and technical personnel should be replaced. With special tools, the bearings should be cleaned thoroughly without removing the stator coil.
