2.2KW Water Cooled Spindle Motor Kit CNC Milling Spindle 2.2KW+ 2.2KW Inverter +80mm Spindle Holder+ER20 Collet For CNC Router
Package introduction:
Set 1: 1*2.2kw water cooled spindle+1*2.2kw inverter+1*water pump+ 1* 5m water pipes+1* 80mm clamp+13pcs *ER20
Set 2: 1pcs 2.2kw water cooled spindle+2.2kw inverter+1pcs water pump+ 1pcs 5m water pipes+1pcs 80mm clamp+13pcs ER20+2M Three-core copper core cable
Set 3: 1pcs 2.2kw water cooled spindle+2.2kw inverter+1pcs water pump+ 1pcs 5m water pipes+1pcs 80mm clamp+13pcs ER20+100mm brushes
Set 4: 1pcs 2.2kw water cooled spindle+2.2kw inverter+1pcs water pump+ 1pcs 5m water pipes+1pcs 80mm clamp+13pcs ER20+10pcs End Mills (different cutting diameter: 0.8mm, 1.0mm, 1.2mm, 1.4mm, 1.6mm, 1.8mm, 2.0mm, 2.2mm, 2.5mm, 3.0mm)
Set 5: 1pcs 2.2kw water cooled spindle+2.2kw inverter+1pcs water pump+ 1pcs 5m water pipes+1pcs 80mm clamp+13pcs ER20+2M Three-core copper core cable+100mm brushes+10pcs End Mills (different cutting diameter: 0.8mm, 1.0mm, 1.2mm, 1.4mm, 1.6mm, 1.8mm, 2.0mm, 2.2mm, 2.5mm, 3.0mm)
Fearture：
1. Water-cooled spindle motor
Size: 80mm
Power: 2200W
Voltage: 220V
Frequency: 0-400Hz
Speed: 0-24000rpm
Water Cooling ER20 collet
Runout off: less than 0.005mm
Germany SKS 4pcs bearing
Bearing type: 4pcs bearing C7005X2 C7002X2
Grease Lubrication
2.Inverter:
Input Voltage: 110V/220V(+/-15%)
We also stock 380V(+/-15%), please contact us.
Output Voltage: 110V/220V AC
Input Frequency: 48-63 Hz
Output Frequency: 0-400 Hz
Input Phase: 1 or 3 phase
Output Phase: 3 phase
The inverter parameters are:
PD005=400
PD004=400
PD003=400
Note that the default parameter of the inverter is 400HZ.
3. 13PCS ER20 Collet :
Gripping Range: 1MM to 13MM (1,2,3.175,4,5,6,7,8,9,10,11,12.7,13mm)
4.Water Pump:
Voltage: 220V
Structure: Single-stage Pump
Pressure: High Pressure
Application: Submersible
Usage: Water
5.5M Water Pipes:
Size:5M 5mm (ID)*8mm (OD)
6.Spindle Motor Clamp Mount:
Diameter: 80mm
Material: Aluminum,Surface sandblasted
Application: Wood working industry rourter, such as wood door milling engraving and cutting, furniture producing
Noted:The hole in the middle of our clamp is not punched through. The middle screw is the jack screw. The function of the two screws on the left and right is to lock. The middle screw function is used when disassembling the spindle. Loosen the screws on both sides and tighten the middle screw, the whole fixture will be opened. the function is easy to take out the spindle.
BUYER SHOWS
